[嵌入式] STC 32位8051单片机开发实例教程二 I/O工作模式及其配置

开发: C++知识库 Java知识库 JavaScript Python PHP知识库人工智能区块链大数据移动开发嵌入式开发工具数据结构与算法开发测试游戏开发网络协议系统运维
教程: HTML教程 CSS教程 JavaScript教程 Go语言教程 JQuery教程 VUE教程 VUE3教程 Bootstrap教程 SQL数据库教程 C语言教程 C++教程 Java教程 Python教程 Python3教程 C#教程
数码: 电脑笔记本显卡显示器固态硬盘硬盘耳机手机 iphone vivo oppo 小米华为单反装机图拉丁

-> 嵌入式 -> STC 32位8051单片机开发实例教程二 I/O工作模式及其配置 -> 正文阅读

[嵌入式]STC 32位8051单片机开发实例教程二 I/O工作模式及其配置

1.?I/O工作模式 STC 32G系列单片机最多有64Pin引脚，最多有60个I/O口。如下图示：

STC32G系列单片机的?I/O口都有4种工作模式：准双向口（弱上拉）、推挽输出（强上拉）、高阻输入（电流不能流入也不能流出）、开漏输出。P30、P31上电复位状态为准双向（弱上拉）模式，其余I/O口上电复位状态为高阻输入，这与STC15系列，有所不同。

要使用I/O口需配置?I/O口的工作模式，STC32G系列单片机除有与工作模式配置有关的端口配置寄存器（PxM0、PxM1）、端口数据寄存器外Px，还有端口上拉电阻控制寄存器（enable/disable 内部4.1K上拉电阻）PxPU、端口施密特触发控制寄存器（enable/disable 施密特触发功能）PxNCS、端口电平转换速度控制寄存器（使转换速度可进行快慢切换）、端口驱动电流控制寄存器（使端口驱动能力能在一般驱动能力与增强驱动能力间切换）PxSR、端口数字信号输入使能控制寄存器（enable/disable 数字信号输入）PxIE、端口下拉电阻控制寄存器（enable/disable内部10K下拉电阻）。较STC15系列单片机要复杂得多。

STC32G系列单片机的?I/O口的工作模式通过端口配置寄存器（PxM0、PxM1）来配置，配置方法如下：

2.不同工作模式下的I/O结构图

?STC32G系列单片机的准双向?I/O结构图如下：

??STC32G系列单片机的推挽输出 I/O结构图如下：

STC32G系列单片机的高阻输入?I/O结构图如下：?

?STC32G系列单片机的开漏 I/O结构图如下：

??STC32G系列单片机相对于STC8位8051单片机新增了4.1K上拉电阻于10K下拉电阻，如下：

?4.库函数? STC 官网上提供了STC32G的库函数目前的最新为第4版，发布日期为2022年6月9号。下载解压后，在library文件夹下可看到的文件如下：

其中STC32G_GPIO.h的代码如下：

/*---------------------------------------------------------------------*/
/* --- STC MCU Limited ------------------------------------------------*/
/* --- STC 1T Series MCU Demo Programme -------------------------------*/
/* --- Mobile: (86)13922805190 ----------------------------------------*/
/* --- Fax: 86-0513-55012956,55012947,55012969 ------------------------*/
/* --- Tel: 86-0513-55012928,55012929,55012966 ------------------------*/
/* --- Web: www.STCMCU.com --------------------------------------------*/
/* --- Web: www.STCMCUDATA.com  ---------------------------------------*/
/* --- QQ:  800003751 -------------------------------------------------*/
/* 如果要在程序中使用此代码,请在程序中注明使用了STC的资料及程序            */
/*---------------------------------------------------------------------*/

#ifndef	__STC32G_GPIO_H
#define	__STC32G_GPIO_H

#include "config.h"

//========================================================================
//                            端口模式设置
//========================================================================
//准双向口
#define  P0_MODE_IO_PU(Pin)				{P0M1 &= ~(Pin), P0M0 &= ~(Pin);}
#define  P1_MODE_IO_PU(Pin)				{P1M1 &= ~(Pin), P1M0 &= ~(Pin);}
#define  P2_MODE_IO_PU(Pin)				{P2M1 &= ~(Pin), P2M0 &= ~(Pin);}
#define  P3_MODE_IO_PU(Pin)				{P3M1 &= ~(Pin), P3M0 &= ~(Pin);}
#define  P4_MODE_IO_PU(Pin)				{P4M1 &= ~(Pin), P4M0 &= ~(Pin);}
#define  P5_MODE_IO_PU(Pin)				{P5M1 &= ~(Pin), P5M0 &= ~(Pin);}
#define  P6_MODE_IO_PU(Pin)				{P6M1 &= ~(Pin), P6M0 &= ~(Pin);}
#define  P7_MODE_IO_PU(Pin)				{P7M1 &= ~(Pin), P7M0 &= ~(Pin);}
//高阻输入
#define  P0_MODE_IN_HIZ(Pin)			{P0M1 |= (Pin), P0M0 &= ~(Pin);}
#define  P1_MODE_IN_HIZ(Pin)			{P1M1 |= (Pin), P1M0 &= ~(Pin);}
#define  P2_MODE_IN_HIZ(Pin)			{P2M1 |= (Pin), P2M0 &= ~(Pin);}
#define  P3_MODE_IN_HIZ(Pin)			{P3M1 |= (Pin), P3M0 &= ~(Pin);}
#define  P4_MODE_IN_HIZ(Pin)			{P4M1 |= (Pin), P4M0 &= ~(Pin);}
#define  P5_MODE_IN_HIZ(Pin)			{P5M1 |= (Pin), P5M0 &= ~(Pin);}
#define  P6_MODE_IN_HIZ(Pin)			{P6M1 |= (Pin), P6M0 &= ~(Pin);}
#define  P7_MODE_IN_HIZ(Pin)			{P7M1 |= (Pin), P7M0 &= ~(Pin);}
//漏极开路
#define  P0_MODE_OUT_OD(Pin)			{P0M1 |= (Pin), P0M0 |= (Pin);}
#define  P1_MODE_OUT_OD(Pin)			{P1M1 |= (Pin), P1M0 |= (Pin);}
#define  P2_MODE_OUT_OD(Pin)			{P2M1 |= (Pin), P2M0 |= (Pin);}
#define  P3_MODE_OUT_OD(Pin)			{P3M1 |= (Pin), P3M0 |= (Pin);}
#define  P4_MODE_OUT_OD(Pin)			{P4M1 |= (Pin), P4M0 |= (Pin);}
#define  P5_MODE_OUT_OD(Pin)			{P5M1 |= (Pin), P5M0 |= (Pin);}
#define  P6_MODE_OUT_OD(Pin)			{P6M1 |= (Pin), P6M0 |= (Pin);}
#define  P7_MODE_OUT_OD(Pin)			{P7M1 |= (Pin), P7M0 |= (Pin);}
//推挽输出
#define  P0_MODE_OUT_PP(Pin)			{P0M1 &= ~(Pin), P0M0 |= (Pin);}
#define  P1_MODE_OUT_PP(Pin)			{P1M1 &= ~(Pin), P1M0 |= (Pin);}
#define  P2_MODE_OUT_PP(Pin)			{P2M1 &= ~(Pin), P2M0 |= (Pin);}
#define  P3_MODE_OUT_PP(Pin)			{P3M1 &= ~(Pin), P3M0 |= (Pin);}
#define  P4_MODE_OUT_PP(Pin)			{P4M1 &= ~(Pin), P4M0 |= (Pin);}
#define  P5_MODE_OUT_PP(Pin)			{P5M1 &= ~(Pin), P5M0 |= (Pin);}
#define  P6_MODE_OUT_PP(Pin)			{P6M1 &= ~(Pin), P6M0 |= (Pin);}
#define  P7_MODE_OUT_PP(Pin)			{P7M1 &= ~(Pin), P7M0 |= (Pin);}

//========================================================================
//                         端口内部4.1K上拉设置
//========================================================================
//上拉使能
#define P0_PULL_UP_ENABLE(Pin)		P0PU |= (Pin)
#define P1_PULL_UP_ENABLE(Pin)		P1PU |= (Pin)
#define P2_PULL_UP_ENABLE(Pin)		P2PU |= (Pin)
#define P3_PULL_UP_ENABLE(Pin)		P3PU |= (Pin)
#define P4_PULL_UP_ENABLE(Pin)		P4PU |= (Pin)
#define P5_PULL_UP_ENABLE(Pin)		P5PU |= (Pin)
#define P6_PULL_UP_ENABLE(Pin)		P6PU |= (Pin)
#define P7_PULL_UP_ENABLE(Pin)		P7PU |= (Pin)
//上拉禁止
#define P0_PULL_UP_DISABLE(Pin)		P0PU &= ~(Pin)
#define P1_PULL_UP_DISABLE(Pin)		P1PU &= ~(Pin)
#define P2_PULL_UP_DISABLE(Pin)		P2PU &= ~(Pin)
#define P3_PULL_UP_DISABLE(Pin)		P3PU &= ~(Pin)
#define P4_PULL_UP_DISABLE(Pin)		P4PU &= ~(Pin)
#define P5_PULL_UP_DISABLE(Pin)		P5PU &= ~(Pin)
#define P6_PULL_UP_DISABLE(Pin)		P6PU &= ~(Pin)
#define P7_PULL_UP_DISABLE(Pin)		P7PU &= ~(Pin)

//========================================================================
//                           端口施密特触发设置
//========================================================================
//施密特触发使能
#define P0_ST_ENABLE(Pin)					P0NCS &= ~(Pin)
#define P1_ST_ENABLE(Pin)					P1NCS &= ~(Pin)
#define P2_ST_ENABLE(Pin)					P2NCS &= ~(Pin)
#define P3_ST_ENABLE(Pin)					P3NCS &= ~(Pin)
#define P4_ST_ENABLE(Pin)					P4NCS &= ~(Pin)
#define P5_ST_ENABLE(Pin)					P5NCS &= ~(Pin)
#define P6_ST_ENABLE(Pin)					P6NCS &= ~(Pin)
#define P7_ST_ENABLE(Pin)					P7NCS &= ~(Pin)
//施密特触发禁止
#define P0_ST_DISABLE(Pin)				P0NCS |= (Pin)
#define P1_ST_DISABLE(Pin)				P1NCS |= (Pin)
#define P2_ST_DISABLE(Pin)				P2NCS |= (Pin)
#define P3_ST_DISABLE(Pin)				P3NCS |= (Pin)
#define P4_ST_DISABLE(Pin)				P4NCS |= (Pin)
#define P5_ST_DISABLE(Pin)				P5NCS |= (Pin)
#define P6_ST_DISABLE(Pin)				P6NCS |= (Pin)
#define P7_ST_DISABLE(Pin)				P7NCS |= (Pin)

//========================================================================
//                          端口电平转换速度设置
//========================================================================
//电平转换慢速，相应的上下冲比较小
#define P0_SPEED_LOW(Pin)					P0SR |= (Pin) 
#define P1_SPEED_LOW(Pin)					P1SR |= (Pin) 
#define P2_SPEED_LOW(Pin)					P2SR |= (Pin) 
#define P3_SPEED_LOW(Pin)					P3SR |= (Pin) 
#define P4_SPEED_LOW(Pin)					P4SR |= (Pin) 
#define P5_SPEED_LOW(Pin)					P5SR |= (Pin) 
#define P6_SPEED_LOW(Pin)					P6SR |= (Pin) 
#define P7_SPEED_LOW(Pin)					P7SR |= (Pin) 
//电平转换快速，相应的上下冲比较大
#define P0_SPEED_HIGH(Pin)				P0SR &= ~(Pin) 
#define P1_SPEED_HIGH(Pin)				P1SR &= ~(Pin) 
#define P2_SPEED_HIGH(Pin)				P2SR &= ~(Pin) 
#define P3_SPEED_HIGH(Pin)				P3SR &= ~(Pin) 
#define P4_SPEED_HIGH(Pin)				P4SR &= ~(Pin) 
#define P5_SPEED_HIGH(Pin)				P5SR &= ~(Pin) 
#define P6_SPEED_HIGH(Pin)				P6SR &= ~(Pin) 
#define P7_SPEED_HIGH(Pin)				P7SR &= ~(Pin) 

//========================================================================
//                          端口驱动电流控制设置
//========================================================================
//一般驱动能力
#define P0_DRIVE_MEDIUM(Pin)			P0DR |= (Pin)
#define P1_DRIVE_MEDIUM(Pin)			P1DR |= (Pin)
#define P2_DRIVE_MEDIUM(Pin)			P2DR |= (Pin)
#define P3_DRIVE_MEDIUM(Pin)			P3DR |= (Pin)
#define P4_DRIVE_MEDIUM(Pin)			P4DR |= (Pin)
#define P5_DRIVE_MEDIUM(Pin)			P5DR |= (Pin)
#define P6_DRIVE_MEDIUM(Pin)			P6DR |= (Pin)
#define P7_DRIVE_MEDIUM(Pin)			P7DR |= (Pin)
//增强驱动能力
#define P0_DRIVE_HIGH(Pin)				P0DR &= ~(Pin)
#define P1_DRIVE_HIGH(Pin)				P1DR &= ~(Pin)
#define P2_DRIVE_HIGH(Pin)				P2DR &= ~(Pin)
#define P3_DRIVE_HIGH(Pin)				P3DR &= ~(Pin)
#define P4_DRIVE_HIGH(Pin)				P4DR &= ~(Pin)
#define P5_DRIVE_HIGH(Pin)				P5DR &= ~(Pin)
#define P6_DRIVE_HIGH(Pin)				P6DR &= ~(Pin)
#define P7_DRIVE_HIGH(Pin)				P7DR &= ~(Pin)

//========================================================================
//                          端口数字信号输入使能
//========================================================================
//使能数字信号输入
#define P0_DIGIT_IN_ENABLE(Pin)		P0IE |= (Pin)
#define P1_DIGIT_IN_ENABLE(Pin)		P1IE |= (Pin)
#define P2_DIGIT_IN_ENABLE(Pin)		P2IE |= (Pin)
#define P3_DIGIT_IN_ENABLE(Pin)		P3IE |= (Pin)
#define P4_DIGIT_IN_ENABLE(Pin)		P4IE |= (Pin)
#define P5_DIGIT_IN_ENABLE(Pin)		P5IE |= (Pin)
#define P6_DIGIT_IN_ENABLE(Pin)		P6IE |= (Pin)
#define P7_DIGIT_IN_ENABLE(Pin)		P7IE |= (Pin)
//禁止数字信号输入
#define P0_DIGIT_IN_DISABLE(Pin)	P0IE &= ~(Pin)
#define P1_DIGIT_IN_DISABLE(Pin)	P1IE &= ~(Pin)
#define P2_DIGIT_IN_DISABLE(Pin)	P2IE &= ~(Pin)
#define P3_DIGIT_IN_DISABLE(Pin)	P3IE &= ~(Pin)
#define P4_DIGIT_IN_DISABLE(Pin)	P4IE &= ~(Pin)
#define P5_DIGIT_IN_DISABLE(Pin)	P5IE &= ~(Pin)
#define P6_DIGIT_IN_DISABLE(Pin)	P6IE &= ~(Pin)
#define P7_DIGIT_IN_DISABLE(Pin)	P7IE &= ~(Pin)

//========================================================================
//                              定义声明
//========================================================================

#define	GPIO_PullUp		0	//上拉准双向口
#define	GPIO_HighZ		1	//浮空输入
#define	GPIO_OUT_OD		2	//开漏输出
#define	GPIO_OUT_PP		3	//推挽输出

#define	GPIO_Pin_0		0x01	//IO引脚 Px.0
#define	GPIO_Pin_1		0x02	//IO引脚 Px.1
#define	GPIO_Pin_2		0x04	//IO引脚 Px.2
#define	GPIO_Pin_3		0x08	//IO引脚 Px.3
#define	GPIO_Pin_4		0x10	//IO引脚 Px.4
#define	GPIO_Pin_5		0x20	//IO引脚 Px.5
#define	GPIO_Pin_6		0x40	//IO引脚 Px.6
#define	GPIO_Pin_7		0x80	//IO引脚 Px.7
#define	GPIO_Pin_LOW	0x0F	//IO低4位引脚
#define	GPIO_Pin_HIGH	0xF0	//IO高4位引脚
#define	GPIO_Pin_All	0xFF	//IO所有引脚

#define	GPIO_P0			0		//
#define	GPIO_P1			1
#define	GPIO_P2			2
#define	GPIO_P3			3
#define	GPIO_P4			4
#define	GPIO_P5			5
#define	GPIO_P6			6
#define	GPIO_P7			7


typedef struct
{
	u8	Mode;		//IO模式,  		GPIO_PullUp,GPIO_HighZ,GPIO_OUT_OD,GPIO_OUT_PP
	u8	Pin;		//要设置的端口	
} GPIO_InitTypeDef;

u8	GPIO_Inilize(u8 GPIO, GPIO_InitTypeDef *GPIOx);

#endif

STC32G_GPIO.c中的代码如下：

/*---------------------------------------------------------------------*/
/* --- STC MCU Limited ------------------------------------------------*/
/* --- STC 1T Series MCU Demo Programme -------------------------------*/
/* --- Mobile: (86)13922805190 ----------------------------------------*/
/* --- Fax: 86-0513-55012956,55012947,55012969 ------------------------*/
/* --- Tel: 86-0513-55012928,55012929,55012966 ------------------------*/
/* --- Web: www.STCMCU.com --------------------------------------------*/
/* --- Web: www.STCMCUDATA.com  ---------------------------------------*/
/* --- QQ:  800003751 -------------------------------------------------*/
/* 如果要在程序中使用此代码,请在程序中注明使用了STC的资料及程序            */
/*---------------------------------------------------------------------*/

#include	"STC32G_GPIO.h"

//========================================================================
// 函数: u8	GPIO_Inilize(u8 GPIO, GPIO_InitTypeDef *GPIOx)
// 描述: 初始化IO口.
// 参数: GPIOx: 结构参数,请参考timer.h里的定义.
// 返回: 成功返回 SUCCESS, 错误返回 FAIL.
// 版本: V1.0, 2012-10-22
//========================================================================
u8	GPIO_Inilize(u8 GPIO, GPIO_InitTypeDef *GPIOx)
{
	if(GPIO > GPIO_P7)				return FAIL;	//错误
	if(GPIOx->Mode > GPIO_OUT_PP)	return FAIL;	//错误
	if(GPIO == GPIO_P0)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P0M1 &= ~GPIOx->Pin,	P0M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P0M1 |=  GPIOx->Pin,	P0M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P0M1 |=  GPIOx->Pin,	P0M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P0M1 &= ~GPIOx->Pin,	P0M0 |=  GPIOx->Pin;	 //推挽输出
	}
	if(GPIO == GPIO_P1)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P1M1 &= ~GPIOx->Pin,	P1M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P1M1 |=  GPIOx->Pin,	P1M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P1M1 |=  GPIOx->Pin,	P1M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P1M1 &= ~GPIOx->Pin,	P1M0 |=  GPIOx->Pin;	 //推挽输出
	}
	if(GPIO == GPIO_P2)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P2M1 &= ~GPIOx->Pin,	P2M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P2M1 |=  GPIOx->Pin,	P2M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P2M1 |=  GPIOx->Pin,	P2M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P2M1 &= ~GPIOx->Pin,	P2M0 |=  GPIOx->Pin;	 //推挽输出
	}
	if(GPIO == GPIO_P3)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P3M1 &= ~GPIOx->Pin,	P3M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P3M1 |=  GPIOx->Pin,	P3M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P3M1 |=  GPIOx->Pin,	P3M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P3M1 &= ~GPIOx->Pin,	P3M0 |=  GPIOx->Pin;	 //推挽输出
	}
	if(GPIO == GPIO_P4)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P4M1 &= ~GPIOx->Pin,	P4M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P4M1 |=  GPIOx->Pin,	P4M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P4M1 |=  GPIOx->Pin,	P4M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P4M1 &= ~GPIOx->Pin,	P4M0 |=  GPIOx->Pin;	 //推挽输出
	}
	if(GPIO == GPIO_P5)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P5M1 &= ~GPIOx->Pin,	P5M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P5M1 |=  GPIOx->Pin,	P5M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P5M1 |=  GPIOx->Pin,	P5M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P5M1 &= ~GPIOx->Pin,	P5M0 |=  GPIOx->Pin;	 //推挽输出
	}
	if(GPIO == GPIO_P6)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P6M1 &= ~GPIOx->Pin,	P6M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P6M1 |=  GPIOx->Pin,	P6M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P6M1 |=  GPIOx->Pin,	P6M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P6M1 &= ~GPIOx->Pin,	P6M0 |=  GPIOx->Pin;	 //推挽输出
	}
	if(GPIO == GPIO_P7)
	{
		if(GPIOx->Mode == GPIO_PullUp)		P7M1 &= ~GPIOx->Pin,	P7M0 &= ~GPIOx->Pin;	 //上拉准双向口
		if(GPIOx->Mode == GPIO_HighZ)			P7M1 |=  GPIOx->Pin,	P7M0 &= ~GPIOx->Pin;	 //浮空输入
		if(GPIOx->Mode == GPIO_OUT_OD)		P7M1 |=  GPIOx->Pin,	P7M0 |=  GPIOx->Pin;	 //开漏输出
		if(GPIOx->Mode == GPIO_OUT_PP)		P7M1 &= ~GPIOx->Pin,	P7M0 |=  GPIOx->Pin;	 //推挽输出
	}
	return SUCCESS;	//成功
}

注意STC32G_GPIO.h中包含了头文件config.h及自定义的数据类型符号，需从Independent_Programme文件夹下的子目录下将下面两个头文件Copy到library文件夹下，否则编译会报错。

下面是我自己写的库函数，头文件如下：

/*STC32G_GPIO.h
  Designed by Bill Liu
  Version 0.0 
  Modified last by Bill Liu on 06/23/2022
*/

#ifndef	__STC32G_GPIO_H
#define	__STC32G_GPIO_H
#include <STC32G.h>
#include "config.h"
#include "mtype.h"

//***************************************
typedef enum
{
  PIN0 = 0x01, 
  PIN1 = 0x02, 
  PIN2 = 0x04, 
  PIN3 = 0x08, 
  PIN4 = 0x10, 
  PIN5 = 0x20, 
  PIN6 = 0x40, 
  PIN7 = 0x80  
}IOPORT_PIN;

//***************************************
typedef enum
{
  SCT_P0 = 0x01, //P0 port
  SCT_P1 = 0x02, //P1 port
  SCT_P2 = 0x04, //P2 port
  SCT_P3 = 0x08, //P3 port
  SCT_P4 = 0x10, //P4 port
  SCT_P5 = 0x20, //P5 port
  SCT_P6 = 0x40, //P6 port
  SCT_P7 = 0x80  //P7 port
}STC32G_IOPORT;

//***************************************
typedef enum
{
  BI_IO = 0, //bidirectional I/O
	PP_OUT,    //push_pull out
	HI_IN,     //high impendence in
	ODR_OUT     //open drain out
}STC32G_IOMODE;

/****************************************
Function: STC32G_P0PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P0PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P0PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_P1PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P1PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P1PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_P2PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P2PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P2PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_P3PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P3PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P3PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_P4PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P4PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P4PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_P5PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P5PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P5PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_P6PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P6PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P6PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_P7PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_P7PinsInit(PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_P7PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

/****************************************
Function: STC32G_PortsPinsInit(ui8 ports,ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);
Return value: void
ports: ports to init
pins: pins to init,
mode: configure work mode
pullUpEnable: 0-pullup disable, 1-pull up enable
pullDownEnable: 0-pull down disable,1-pull down enable
drvEn: 1-drive ability enhance enable, 0-drive ability enhance disable
speedHi; 1- I/O speed high enable, 0- I/O speed high disable
dIEnable: 1- digital singal input enable, 0- digital singal input enable
sTEnable: 1-schmitt trigger enable, 0-schmitt trigger disable
Example:
STC32G_PortsPinsInit(SCT_P0|SCT_P1|SCT_P6,PIN0|PIN3, BI_IO, 0, 0,0,1,1,1);
****************************************/
void STC32G_PortsPinsInit(ui8 ports,ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable);

#endif

库函数源代码如下：

/*STC32G_GPIO.h
  Designed by Bill Liu
  Version 0.0 
  Modified last by Bill Liu on 06/23/2022
*/

#include	"STC32G_GPIO.h"

//*********************************************************************************************************************************************/
void STC32G_P0PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P0M1 &= ~pins;
			P0M0 &= ~pins;
			break;
		case PP_OUT:
			P0M1 &= ~pins;
			P0M0 |= pins;
			break;
		case HI_IN:
			P0M1 |= pins;
			P0M0 &= pins;
			break;
		case ODR_OUT:
			P0M1 |= pins;
			P0M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P0PU |= pins;
	else
		P0PU &= ~pins;
	if(pullDownEnable)
		P0DR |= pins;
	else
		P0DR &= ~pins;
	if(drvEn)
		P0DR &= ~pins;
	else
		P0DR |= pins;
	if(speedHi)
		P0SR &= ~pins;
	else
		P0SR |= pins;
	if(dIEnable)
		P0IE |= pins;
	else
		P0IE &= ~pins;
	if(sTEnable)
		P0NCS &= ~pins;
	else
		P0NCS |= pins;
}
//End of STC32G_P0PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

//*********************************************************************************************************************************************/
void STC32G_P1PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P1M1 &= ~pins;
			P1M0 &= ~pins;
			break;
		case PP_OUT:
			P1M1 &= ~pins;
			P1M0 |= pins;
			break;
		case HI_IN:
			P1M1 |= pins;
			P1M0 &= pins;
			break;
		case ODR_OUT:
			P1M1 |= pins;
			P1M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P1PU |= pins;
	else
		P1PU &= ~pins;
	if(pullDownEnable)
		P1DR |= pins;
	else
		P1DR &= ~pins;
	if(drvEn)
		P1DR &= ~pins;
	else
		P1DR |= pins;
	if(speedHi)
		P1SR &= ~pins;
	else
		P1SR |= pins;
	if(dIEnable)
		P1IE |= pins;
	else
		P1IE &= ~pins;
	if(sTEnable)
		P1NCS &= ~pins;
	else
		P1NCS |= pins;
}
//End of STC32G_P1PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

//**********************************************************************************************************************************************/
void STC32G_P2PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P2M1 &= ~pins;
			P2M0 &= ~pins;
			break;
		case PP_OUT:
			P2M1 &= ~pins;
			P2M0 |= pins;
			break;
		case HI_IN:
			P2M1 |= pins;
			P2M0 &= pins;
			break;
		case ODR_OUT:
			P2M1 |= pins;
			P2M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P2PU |= pins;
	else
		P2PU &= ~pins;
	if(pullDownEnable)
		P2DR |= pins;
	else
		P2DR &= ~pins;
	if(drvEn)
		P2DR &= ~pins;
	else
		P2DR |= pins;
	if(speedHi)
		P2SR &= ~pins;
	else
		P2SR |= pins;
	if(dIEnable)
		P2IE |= pins;
	else
		P2IE &= ~pins;
	if(sTEnable)
		P2NCS &= ~pins;
	else
		P2NCS |= pins;
}
//End of STC32G_P2PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

//*********************************************************************************************************************************************/
void STC32G_P3PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P3M1 &= ~pins;
			P3M0 &= ~pins;
			break;
		case PP_OUT:
			P3M1 &= ~pins;
			P3M0 |= pins;
			break;
		case HI_IN:
			P3M1 |= pins;
			P3M0 &= pins;
			break;
		case ODR_OUT:
			P3M1 |= pins;
			P3M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P3PU |= pins;
	else
		P3PU &= ~pins;
	if(pullDownEnable)
		P3DR |= pins;
	else
		P3DR &= ~pins;
	if(drvEn)
		P3DR &= ~pins;
	else
		P3DR |= pins;
	if(speedHi)
		P3SR &= ~pins;
	else
		P3SR |= pins;
	if(dIEnable)
		P3IE |= pins;
	else
		P3IE &= ~pins;
	if(sTEnable)
		P3NCS &= ~pins;
	else
		P3NCS |= pins;
}
//End of STC32G_P3PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

//**********************************************************************************************************************************************/
void STC32G_P4PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P4M1 &= ~pins;
			P4M0 &= ~pins;
			break;
		case PP_OUT:
			P4M1 &= ~pins;
			P4M0 |= pins;
			break;
		case HI_IN:
			P4M1 |= pins;
			P4M0 &= pins;
			break;
		case ODR_OUT:
			P4M1 |= pins;
			P4M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P4PU |= pins;
	else
		P4PU &= ~pins;
	if(pullDownEnable)
		P4DR |= pins;
	else
		P4DR &= ~pins;
	if(drvEn)
		P4DR &= ~pins;
	else
		P4DR |= pins;
	if(speedHi)
		P4SR &= ~pins;
	else
		P4SR |= pins;
	if(dIEnable)
		P4IE |= pins;
	else
		P4IE &= ~pins;
	if(sTEnable)
		P4NCS &= ~pins;
	else
		P4NCS |= pins;
}
//End of STC32G_P4PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

//**********************************************************************************************************************************************/
void STC32G_P5PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P5M1 &= ~pins;
			P5M0 &= ~pins;
			break;
		case PP_OUT:
			P5M1 &= ~pins;
			P5M0 |= pins;
			break;
		case HI_IN:
			P5M1 |= pins;
			P5M0 &= pins;
			break;
		case ODR_OUT:
			P5M1 |= pins;
			P5M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P5PU |= pins;
	else
		P5PU &= ~pins;
	if(pullDownEnable)
		P5DR |= pins;
	else
		P5DR &= ~pins;
	if(drvEn)
		P5DR &= ~pins;
	else
		P5DR |= pins;
	if(speedHi)
		P5SR &= ~pins;
	else
		P5SR |= pins;
	if(dIEnable)
		P5IE |= pins;
	else
		P5IE &= ~pins;
	if(sTEnable)
		P5NCS &= ~pins;
	else
		P5NCS |= pins;
}
//End of STC32G_P5PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

//**********************************************************************************************************************************************/
void STC32G_P6PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P6M1 &= ~pins;
			P6M0 &= ~pins;
			break;
		case PP_OUT:
			P6M1 &= ~pins;
			P6M0 |= pins;
			break;
		case HI_IN:
			P6M1 |= pins;
			P6M0 &= pins;
			break;
		case ODR_OUT:
			P6M1 |= pins;
			P6M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P6PU |= pins;
	else
		P6PU &= ~pins;
	if(pullDownEnable)
		P6DR |= pins;
	else
		P6DR &= ~pins;
	if(drvEn)
		P6DR &= ~pins;
	else
		P6DR |= pins;
	if(speedHi)
		P6SR &= ~pins;
	else
		P6SR |= pins;
	if(dIEnable)
		P6IE |= pins;
	else
		P6IE &= ~pins;
	if(sTEnable)
		P6NCS &= ~pins;
	else
		P6NCS |= pins;
}
//End of STC32G_P6PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

//**********************************************************************************************************************************************/
void STC32G_P7PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	SysInit();
	switch(mode)
	{
		case BI_IO:
			P7M1 &= ~pins;
			P7M0 &= ~pins;
			break;
		case PP_OUT:
			P7M1 &= ~pins;
			P7M0 |= pins;
			break;
		case HI_IN:
			P7M1 |= pins;
			P7M0 &= pins;
			break;
		case ODR_OUT:
			P7M1 |= pins;
			P7M0 |= pins;
			break;
	}
	if(pullUpEnable)
		P7PU |= pins;
	else
		P7PU &= ~pins;
	if(pullDownEnable)
		P7DR |= pins;
	else
		P7DR &= ~pins;
	if(drvEn)
		P7DR &= ~pins;
	else
		P7DR |= pins;
	if(speedHi)
		P7SR &= ~pins;
	else
		P7SR |= pins;
	if(dIEnable)
		P7IE |= pins;
	else
		P7IE &= ~pins;
	if(sTEnable)
		P7NCS &= ~pins;
	else
		P7NCS |= pins;
}
//End of STC32G_P7PinsInit(ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

/***************************************************************************************************************************************************/
void STC32G_PortsPinsInit(ui8 ports,ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)
{
	ui8 i;
	for(i = 0; i < 8; i++)
	{
		if(ports & (1 << i))
		{
			switch(i)
			{
				case 0:
					STC32G_P0PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
				case 1:
					STC32G_P1PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
				case 2:
					STC32G_P2PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
				case 3:
					STC32G_P3PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
				case 4:
					STC32G_P4PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
				case 5:
					STC32G_P5PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
				case 6:
					STC32G_P6PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
				case 7:
					STC32G_P7PinsInit(pins, mode, pullUpEnable, pullDownEnable,drvEn,speedHi,dIEnable, sTEnable);
					break;
			}
		}
	}
}
//End of STC32G_PortsPinsInit(ui8 ports,ui8 pins, STC32G_IOMODE mode, BOOL pullUpEnable, BOOL pullDownEnable,BOOL drvEn,BOOL speedHi,BOOL dIEnable, BOOL sTEnable)

我也将config.h 做了修改，修改后的代码如下：

/*STC32G_GPIO.h
  Designed by Bill Liu
  Version 0.0 
  Modified last by Bill Liu on 06/23/2022
*/
#ifndef __CONFIG_H__
#define __CONFIG_H__

#define FOSC                    35000000UL
//#define FOSC                    24000000UL
//#define FOSC                    27000000UL
//#define FOSC                    30000000UL
//#define FOSC                    33177600UL



//********************************************************
void SysInit(); //init System speed  fastest


#endif

config.c的源代码如下：

/*config.c
  Designed by Bill Liu
  Version 0.0 
  Modified last by Bill Liu on 06/22/2022
*/

#include <STC32G.h>
#include "config.h"

//********************************************************
void SysInit() //init System speed  fastest
{
	EAXFR = 1;		//visit XFR enable
	CKCON = 0x00; //set outer data bus speed fastest
	WTST = 0x00;  //CPU wait 0 to run program
}
//End of SysInit()

5. I/O配置实例下面将用我自己写的库函数来演示验证I/O配置。我将以下面这块板来做验证

?这块板用白线隔开将板分成了三个区域，左边为电源区，中间为模拟采样及MCU区域，右边为逻辑输入输出区。再看一下单片机的型号：

?先编译下面的空程序，将其下载到单片机中，看能否下在成功。

/*main.c
  Designed by Bill Liu
  Version 0.0 
  Modified last by Bill Liu on 06/22/2022
*/

#include "main.h"
#include "config.h"

void main()
{
	
}
//End of main()

?下载成功，如下：

?测一下I/O口的输出电压，随意选一个I/O口测试（实际测试的是P73），测试结果如下。

视乎输出了低电平，应该是既不输出高电平也不输出低电平（没电流流入，也没电流流出), 看它能否驱动Led,下面是一个能够正常点亮的LED：

先将接电源端不变，另一端将其接在与P73连接的排针上，看LED是否任被点亮，结果如下：

LED未被点亮?说明确实没有电流输入。SCT32G上电复位时I/O口处于高阻输入状态，一方面可以增强抗干扰能力，另一方面可以避免该单片机控制的电路载单片机上电复位时误动作。

在main()函数中插入如下代码：

void main()
{
	STC32G_P7PinsInit(PIN3, BI_IO, 0, 0, 0, 0, 0, 0);
	P73 = 0;
	while(1);
}
//End of main()

编译下载，如果库函数没有问题，LED应该亮起，结果如下：

说明库函数没有错误。将main()函数中的代码修改如下：

void main()
{
	STC32G_P7PinsInit(PIN3, BI_IO, 0, 0, 0, 0, 0, 0);
	P73 = 1;
	while(1);
}
//End of main()

?编译下载到单片机，先来测试下双向I/O弱上拉的正向驱动能力。结果如下：

LED仅发出微弱的亮光，说明I/O正向驱动能力弱。现将上拉电阻使能，即库函数的第三个参数设为1，修改main()函数中的代码如下：

void main()
{
	STC32G_P7PinsInit(PIN3, BI_IO, 1, 0, 0, 0, 0, 0);
	P73 = 1;
	while(1);
}
//End of main()

编译下载后的结果如下：

?LED变亮，说明正向驱动能力有所增强。现将驱动电流增大，将下面红框中的变量设为1，看下结果如和变化：

void main()
{
	STC32G_P7PinsInit(PIN3, BI_IO, 0, 0, 1, 0, 0, 0);
	P73 = 1;
	while(1);
}
//End of main()

?编译下载，结果如下：

感觉与双向I/O弱上拉的正向驱动能力差不多。再看一下，打开下拉电阻时双向I/O弱上拉的正向驱动能力。修改main()函数代码如下：

void main()
{
	STC32G_P7PinsInit(PIN3, BI_IO, 0, 1, 0, 0, 0, 0);
	P73 = 1;
	while(1);
}
//End of main()

编译下载到单片机的结果如下：

?感觉LED亮度变化并不明显。

STC32G的 I/O 较STC15? 的I/O新增新的功能与寄存器，从上面的测试可以看出，I/O的负向驱动能力较强（可承受较大的灌电流），正向驱动能力弱，如果要使I/O口有较大的正向驱动能力，需将其设置为推挽模式，如果设置为双向I/O，需使能上拉电阻才能使其正向驱动能力有所提升，使能PxDR对提供双向I/O的正向驱动能力并不明显，可能仅是对提高I/O的电平转换速度有用。

下面再测试一下I/O的读写，将main()函数的代码修改如下：

void main()
{
	STC32G_P7PinsInit(PIN3, BI_IO, 1, 0, 1, 0, 1, 0);
	P73 = 1;
	STC32G_P0PinsInit(0xFF, BI_IO, 0, 0, 0, 0, 1, 1); //init to bidirectional I/O, pull up disable, pull down disable , dive ability enhance disable, 
	//high speed disable, digital singal input enable, schmitt trigger enable
	STC32G_P2PinsInit(0xFF, BI_IO, 0, 0, 0, 0, 1, 1);
    P0 = 0xA0;
    P2 = 0xFF；
	while(1)
	{
		
		if(P2==P0)
			P73 = 1;
		else
			P73 = 0;
	}
}
//End of main()

编译下载后的结果如下：

?LED为P73正向驱动，LED亮，说明P2、P0正常读取数据。现将将main()函数的代码修改如下：

void main()
{
	STC32G_P7PinsInit(PIN3, BI_IO, 1, 0, 1, 0, 1, 0);
	P73 = 1;
	STC32G_P0PinsInit(0xFF, BI_IO, 0, 0, 0, 0, 1, 1); //init to bidirectional I/O, pull up disable, pull down disable , dive ability enhance disable, 
	//high speed disable, digital singal input enable, schmitt trigger enable
	STC32G_P2PinsInit(0xFF, BI_IO, 0, 0, 0, 0, 1, 0);
    P0 = 0xA0;
    P2 = 0xFF；
	while(1)
	{
		
		if(P2==P0)
			P73 = 1;
		else
			P73 = 0;
	}
}
//End of main()

?编译下载结果如下：